Lean pipes need to be designed with load capacity in mind. Strength can be increased by adding fulcrum, connecting parts and parallel use of double cladding plastic pipes. When designing the structure, make sure that the main load is applied directly to the pipe fittings and not to the connections.

　　The maximum horizontal distance is every 600mm (according to the specific weight of the design of the specific structure) can be built at will, using block type assembly, must be vertical with the ground column support, and every 1200mm, vertical column should be directly to the ground. In the case of products with casters, the underframe shall be of double rod parallel construction. The horizontal distance is 600mm, and the safety bearing of a single rod and slide is 30kg. A whole plastic covering than by the collet string up a few plastic tube strength is stronger, so in the plastic covering tube selection, the stress rod must be the whole rod, the connecting rod can be segmenting.

　　When designing a rod product, the usage should be considered in detail. If it does not need to move, try not to design a product with casters. Line bar products are also known as flexible, according to your site conditions and customer requirements, comprehensive design scheme, flexible disassembly and installation, no welding, practical, automotive, electronics, printing, clothing, dust workshop, installation is more health, no pollution.

　　The width of each column of the sliding shelf (center distance) is the width of the turnover box placed +60mm; The height of each floor is +50mm of the height of the turnover box placed. The determination of the slope Angle of the slide, the general slope Angle of the slide is 5~8 degrees, when placing precision materials, heavy materials and the bottom of the turnover box is smooth, the slope Angle should be smaller.

Lean pipe has been widely used in the world. Its outer layer has plastic coating layer, the middle is a metal layer, and the inner layer is an anti-rust layer. This kind of lean pipe has low cost, but strong practicability, and it is an essential basic material for logistics industry and manufacturing industry.

Production line has many names, including lean pipe and coated pipe. It is generally used with lean pipe joint. Lean pipe is the basic assembly material of lean workbench, shelf and turnover car.

The production line is designed with load capacity in mind, and its strength can be increased by adding fulcrum, connecting parts, and by using double covered plastic tubes in parallel. When designing the structure, ensure that the main load is applied directly to the pipe fitting and not to the coupling. The maximum horizontal distance every 600mm (according to the specific weight to design the specific structure) can be built at will, the building block assembly method, must be supported by vertical columns and the ground, and every 1200mm, vertical columns should be directly to the ground. For castor products, the chassis shall be of double rod parallel construction. The horizontal distance is 600mm. The safe bearing capacity of a single cable rod and guide rail is 30kg.

The strength of a whole plastic cover is stronger than that of several plastic cover pipes connected by the collet string, so when the plastic cover pipe is selected, the rod must be the whole root, and the connecting rod can be segmented. The width of each column of sliding shelves (center distance) is the width of the turnover box placed +60mm; The height of each layer is the height of the turnover box +50mm.

Determine the incline Angle of the guide rail. Generally, the incline Angle of the guide rail is 5 to 8 degrees. When placing precision materials, heavy materials, and the bottom of the revolving box is smooth, the incline Angle should be smaller.

The use of lean pipe products should be carefully considered when designing them. If they do not need to be moved, they should not be designed as casters. Lean pipe products are also known as flexible, according to your site situation and customer requirements, comprehensive design scheme, flexible disassembly and assembly, no welding, practical, automobile, electronics, printing, clothing, dust-proof workshop, installation more sanitary, pollution-free.

Are you curious about whether aluminum tubes are recyclable? In this article, we delve into the world of recycling and explore the sustainability of aluminum tubes. Join us as we uncover the benefits of recycling aluminum tubes and learn how you can make a positive impact on the environment.

1. The Benefits of Recycling Aluminum Tubes

Aluminum is one of the most recyclable materials on the planet, and aluminum tubes are no exception. The process of recycling aluminum tubes not only helps to reduce waste in landfills, but it also conserves energy and natural resources. When aluminum tubes are recycled, they can be turned into new products with minimal loss of quality or performance. This makes aluminum recycling a sustainable and environmentally friendly option for manufacturers and consumers alike.

2. How to Properly Recycle Aluminum Tubes

When it comes to recycling aluminum tubes, there are a few key steps to keep in mind. First, it's important to make sure that the tubes are clean and free of any contaminants before recycling. This can help to ensure that the aluminum tubes can be properly processed and turned into new products. Additionally, it's important to separate aluminum tubes from other materials, such as plastic or paper, to make the recycling process more efficient. By following these steps, you can help to ensure that your aluminum tubes are recycled properly and effectively.

3. The Environmental Impact of Aluminum Tube Recycling

Recycling aluminum tubes has a positive impact on the environment in a number of ways. For starters, recycling aluminum tubes helps to reduce the amount of waste that ends up in landfills, which can help to mitigate the negative effects of landfill pollution. In addition, recycling aluminum tubes also helps to conserve energy and natural resources, as it takes significantly less energy to recycle aluminum than it does to produce new aluminum from raw materials. By choosing to recycle aluminum tubes, you can help to reduce your carbon footprint and protect the planet for future generations.

4. Sunqit's Commitment to Aluminum Tube Recycling

At Sunqit, we are committed to sustainability and environmental responsibility. That's why we make it a priority to recycle all of our aluminum tubes in an efficient and effective manner. By partnering with reputable recycling facilities, we ensure that our aluminum tubes are properly processed and turned into new products, rather than ending up in landfills. By choosing Sunqit products, you can feel confident knowing that you are supporting a brand that prioritizes sustainability and eco-friendliness.

5. The Future of Aluminum Tube Recycling

As awareness of the importance of recycling continues to grow, the future of aluminum tube recycling looks bright. With advancements in recycling technology and increased education about the benefits of recycling, more and more consumers and manufacturers are choosing to recycle their aluminum tubes. This trend is likely to continue in the coming years, as the need for sustainable and eco-friendly practices becomes increasingly apparent. By choosing to recycle your aluminum tubes, you can play a part in creating a more sustainable future for our planet.

Conclusion

In conclusion, aluminum tubes are indeed recyclable and play a crucial role in sustainable packaging solutions. By choosing to recycle aluminum tubes, we can help reduce the amount of waste that ends up in landfills and conserve valuable resources. With a little effort from each of us, we can make a big impact on the environment and ensure that future generations can continue to enjoy the benefits of this versatile and eco-friendly packaging option. So let's all do our part and opt for recyclable aluminum tubes whenever possible. Together, we can make a difference and create a more sustainable world for all.

Lean tube does not contain heavy metal elements, zero pollution, and can be completely recycled. Furthermore, due to the strong anti-corrosion of lean pipe, the surface hardness far exceeds that of stainless steel, its strength is also twice as common as the same wall thickness steel pipe.

In addition to reducing the time and movement necessary to pick and place parts and tools, Lean Tubes can help reduce the risk of injury in the workplace.

The main components of the lean pipe are covered with plastic, and new accessories that can be matched with the original lean rack can be designed to increase the use of different production methods or different work stations according to the needs of different products.

The lean tube is lightweight, and the surface resistance of the lean tube is extremely low, making it an ideal antistatic material.

What are the inspection standards for lean pipe joints? Below, we will share with you that the inspection standards for lean pipe joints mainly include the following aspects:

1. Appearance quality inspection: Ensure that the appearance of the storage joint has no obvious defects, such as cracks, bubbles, burrs, rust spots, dents, etc., to ensure its normal function during installation and use.

2. Material composition analysis: By using spectral analysis, chemical analysis and other methods to detect the chemical composition of the pipe joint material, confirm whether its material meets the design requirements, and ensure that it has the required strength, corrosion resistance, high temperature resistance and other characteristics.

3. Mechanical performance testing: Evaluate the tensile strength, yield strength, hardness, and other mechanical properties of pipe joints to ensure that they will not fracture or deform during use.

4. Pressure performance testing: Evaluate the sealing and strength of pipe joints under pressure, including pressure resistance testing and burst pressure testing, to ensure their safe use in high-pressure pipeline systems.

5. Sealing performance testing: Ensure that the joint and pipeline are effectively sealed after connection to prevent medium leakage.